Fairlane Owners/Enthusiasts Forum Index
  The time now is Mon Jun 26, 2017 2:08 pm   

Bookmark this site!

Fairlane Owners/Enthusiasts Forum Index -> Wanted

62 window trim
Goto page 1, 2  Next
  Author    Thread Post new topic Reply to topic
Bill62
Senior Member


Joined: 30 May 2006
Posts: 278
62 window trim

I need the trim around the pass. rear window

Post Mon Feb 15, 2010 11:43 am 
 View user's profile Send private message Send e-mail  Reply with quote  
roger
Senior Member


Joined: 09 Mar 2006
Posts: 1008
Location: ontario, canada
62vs63

bill: is the 63 trim the same?
I can check that 63 in my local yard if its a fit.
and by window trim, you mean the chrome trim up the pillar & then around top of window?
Bout all thats left of the old girl last time i was there pulling the vent windows
_________________
roger powell

Post Thu Feb 18, 2010 12:46 pm 
 View user's profile Send private message Send e-mail  Reply with quote  
Bill62
Senior Member


Joined: 30 May 2006
Posts: 278

Hey Roger Im not sure if the 63 is the same. The piece you discribed is what I need

Post Fri Feb 19, 2010 7:51 am 
 View user's profile Send private message Send e-mail  Reply with quote  
roger
Senior Member


Joined: 09 Mar 2006
Posts: 1008
Location: ontario, canada
trim

I'm going over there to look at a mod motor tomorrow
I'll measure my 62's trim, but, i;ll bet 62-63 window trim is the same
If it is, i'll pull it, although i just realized that window trim is about the only trim i;ve never had to pull
Any idea on how it comes off, I'm assuming its press fit or hooked over an edge somehow?
This is all assuming that 63 has the chrome trim you want, it is a F;lane 500
_________________
roger powell

Post Tue Feb 23, 2010 2:13 pm 
 View user's profile Send private message Send e-mail  Reply with quote  
Bill62
Senior Member


Joined: 30 May 2006
Posts: 278

It should just fit over the window. there is no screws

Post Wed Feb 24, 2010 3:38 pm 
 View user's profile Send private message Send e-mail  Reply with quote  
roger
Senior Member


Joined: 09 Mar 2006
Posts: 1008
Location: ontario, canada
picked clean

The old 63 is about cleaned, Bill, someone beat me to the trim
All thats left thats usuable is
hood
trunk lid
rear seats
_________________
roger powell

Post Thu Feb 25, 2010 2:49 pm 
 View user's profile Send private message Send e-mail  Reply with quote  
Bill62
Senior Member


Joined: 30 May 2006
Posts: 278

Thanks anyway Roger

Post Fri Feb 26, 2010 8:31 am 
 View user's profile Send private message Send e-mail  Reply with quote  
Bill62
Senior Member


Joined: 30 May 2006
Posts: 278

Still no luck.......

Post Thu Mar 18, 2010 5:04 pm 
 View user's profile Send private message Send e-mail  Reply with quote  
Bill62
Senior Member


Joined: 30 May 2006
Posts: 278

I also need the drivers side vent window. along with the trim around the pass rear window. Can anyone help me?

Post Wed Mar 31, 2010 12:07 pm 
 View user's profile Send private message Send e-mail  Reply with quote  
mygirls63
Senior Member


Joined: 09 Mar 2006
Posts: 416
Location: Kansas

Bill,

I will have to go look, but I used to have a couple of vent window assemblies. I know for a fact that the passenger side is for a hard top, but I had 2 sedan vents at one time. I do know that the rubber was wasted on them, so I may have tossed them. I cut one up to see if I could do Lexan in them, but the cost of new seals was too high for my taste.

I will look and let you know.
_________________
Scott
1963 Fairlane Mini tub 10pt cage New 408" C4 Canfield 195CC heads Comp solid roller Victor Jr. 9" w/4.11? gears Moser spool & 35 spline axles. www.marksullense85carburetors.com

Post Wed Mar 31, 2010 8:09 pm 
 View user's profile Send private message Send e-mail  Reply with quote  
mygirls63
Senior Member


Joined: 09 Mar 2006
Posts: 416
Location: Kansas

Sorry, I pitched them. All I have left is a pair of V-8 front springs, window regulators, the right hand hard top vent window and the heater control panel.
_________________
Scott
1963 Fairlane Mini tub 10pt cage New 408" C4 Canfield 195CC heads Comp solid roller Victor Jr. 9" w/4.11? gears Moser spool & 35 spline axles. www.marksullense85carburetors.com

Post Wed Mar 31, 2010 8:15 pm 
 View user's profile Send private message Send e-mail  Reply with quote  
Bill62
Senior Member


Joined: 30 May 2006
Posts: 278

Thanks for looking. My vent window handle broke off so I don't need the whole assy but I thought it would be esier to locate one

Post Thu Apr 01, 2010 6:40 am 
 View user's profile Send private message Send e-mail  Reply with quote  
69supercj
Member


Joined: 25 Jul 2006
Posts: 65
Location: Fair Grove, MO

Is this for a two door or 4? Hardtop or sedan?

Post Fri Apr 02, 2010 9:57 pm 
 View user's profile Send private message  Reply with quote  
Bill62
Senior Member


Joined: 30 May 2006
Posts: 278

Its a 2 door post

Post Sat Apr 03, 2010 5:07 pm 
 View user's profile Send private message Send e-mail  Reply with quote  
John G
Junior Member


Joined: 24 Nov 2009
Posts: 42
Location: Riverside California

I don't know where you are located but, there is a seller on Craigslist with 1962 Parts. He says he has and I quote, "an ass load of parts, 3 of everything." Anyway, his name is Jacob (434) 607-0633, Richmond Virginia. Good Luck!

Post Tue Apr 06, 2010 12:12 am 
 View user's profile Send private message  Reply with quote  
  Display posts from previous:      
Post new topic Reply to topic

Jump to:  
Goto page 1, 2  Next

Last Thread | Next Thread  >

Forum Rules:
You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum

 

Powered by phpBB © 2001 phpBB Group
phpXP2 Template by Vereor.

This theme is to be used only for the promotion of Windows(TM) XP and its associated products. - Read the full disclaimer
I, the developer, take no responsibility for use of this theme against the wishes of Microsoft(R).

Create your own free forum now!
Terms of Service Purchase Ad Removal Forum Archive Report Abuse