Author
|
Thread |
|
|
Bill62
Senior Member
Joined: 30 May 2006
Posts: 278
|
62 window trim
I need the trim around the pass. rear window
|
Mon Feb 15, 2010 11:43 am |
|
|
roger
Senior Member
Joined: 09 Mar 2006
Posts: 1008
Location: ontario, canada |
62vs63
bill: is the 63 trim the same?
I can check that 63 in my local yard if its a fit.
and by window trim, you mean the chrome trim up the pillar & then around top of window?
Bout all thats left of the old girl last time i was there pulling the vent windows _________________ roger powell
|
Thu Feb 18, 2010 12:46 pm |
|
|
Bill62
Senior Member
Joined: 30 May 2006
Posts: 278
|
Hey Roger Im not sure if the 63 is the same. The piece you discribed is what I need
|
Fri Feb 19, 2010 7:51 am |
|
|
roger
Senior Member
Joined: 09 Mar 2006
Posts: 1008
Location: ontario, canada |
trim
I'm going over there to look at a mod motor tomorrow
I'll measure my 62's trim, but, i;ll bet 62-63 window trim is the same
If it is, i'll pull it, although i just realized that window trim is about the only trim i;ve never had to pull
Any idea on how it comes off, I'm assuming its press fit or hooked over an edge somehow?
This is all assuming that 63 has the chrome trim you want, it is a F;lane 500 _________________ roger powell
|
Tue Feb 23, 2010 2:13 pm |
|
|
Bill62
Senior Member
Joined: 30 May 2006
Posts: 278
|
It should just fit over the window. there is no screws
|
Wed Feb 24, 2010 3:38 pm |
|
|
roger
Senior Member
Joined: 09 Mar 2006
Posts: 1008
Location: ontario, canada |
picked clean
The old 63 is about cleaned, Bill, someone beat me to the trim
All thats left thats usuable is
hood
trunk lid
rear seats _________________ roger powell
|
Thu Feb 25, 2010 2:49 pm |
|
|
Bill62
Senior Member
Joined: 30 May 2006
Posts: 278
|
Thanks anyway Roger
|
Fri Feb 26, 2010 8:31 am |
|
|
Bill62
Senior Member
Joined: 30 May 2006
Posts: 278
|
Still no luck.......
|
Thu Mar 18, 2010 5:04 pm |
|
|
Bill62
Senior Member
Joined: 30 May 2006
Posts: 278
|
I also need the drivers side vent window. along with the trim around the pass rear window. Can anyone help me?
|
Wed Mar 31, 2010 12:07 pm |
|
|
mygirls63
Senior Member
Joined: 09 Mar 2006
Posts: 416
Location: Kansas |
Bill,
I will have to go look, but I used to have a couple of vent window assemblies. I know for a fact that the passenger side is for a hard top, but I had 2 sedan vents at one time. I do know that the rubber was wasted on them, so I may have tossed them. I cut one up to see if I could do Lexan in them, but the cost of new seals was too high for my taste.
I will look and let you know. _________________ Scott
1963 Fairlane Mini tub 10pt cage New 408" C4 Canfield 195CC heads Comp solid roller Victor Jr. 9" w/4.11? gears Moser spool & 35 spline axles. www.marksullense85carburetors.com
|
Wed Mar 31, 2010 8:09 pm |
|
|
mygirls63
Senior Member
Joined: 09 Mar 2006
Posts: 416
Location: Kansas |
Sorry, I pitched them. All I have left is a pair of V-8 front springs, window regulators, the right hand hard top vent window and the heater control panel. _________________ Scott
1963 Fairlane Mini tub 10pt cage New 408" C4 Canfield 195CC heads Comp solid roller Victor Jr. 9" w/4.11? gears Moser spool & 35 spline axles. www.marksullense85carburetors.com
|
Wed Mar 31, 2010 8:15 pm |
|
|
Bill62
Senior Member
Joined: 30 May 2006
Posts: 278
|
Thanks for looking. My vent window handle broke off so I don't need the whole assy but I thought it would be esier to locate one
|
Thu Apr 01, 2010 6:40 am |
|
|
69supercj
Member
Joined: 25 Jul 2006
Posts: 65
Location: Fair Grove, MO |
Is this for a two door or 4? Hardtop or sedan?
|
Fri Apr 02, 2010 9:57 pm |
|
|
Bill62
Senior Member
Joined: 30 May 2006
Posts: 278
|
Its a 2 door post
|
Sat Apr 03, 2010 5:07 pm |
|
|
John G
Junior Member
Joined: 24 Nov 2009
Posts: 42
Location: Riverside California |
I don't know where you are located but, there is a seller on Craigslist with 1962 Parts. He says he has and I quote, "an ass load of parts, 3 of everything." Anyway, his name is Jacob (434) 607-0633, Richmond Virginia. Good Luck!
|
Tue Apr 06, 2010 12:12 am |
|
|